Basic Construction And Carpentry Techniques Home







Google




MISSION FURNITURE

HOW TO MAKE IT

PART THREE


POPULAR MECHANICS HANDBOOKS

CHICAGO

POPULAR MECHANICS COMPANY

Copyrighted, 1912 BY H. H. WINDSOR


MAGAZINE RACK

The accompanying cut shows a magazine rack that will find favor with many amateur wood-workers on account of its simplicity in design and its rich, massive appearance when properly finished. It is so constructed that each piece may be polished, stained and finished before it is finally put together. Quarter-sawed oak is the best wood to use. Plain-sawed oak looks well, but it is more liable to warp than quarter-sawed and this is quite an element in pieces as wide as the ones here used. Following is a list of the material needed:

Considerable labor can be saved if the material be ordered from the mill ready cut to length, squared and sanded. The corner posts should be made first. The most convenient and accurate method of laying out the mortises is to square one end of each post and lay them on the bench flat, with the squared ends even with each other; then clamp them securely and lay out the mortises on one side across all four pieces at once; then loosen the clamp and project the marks to the other side with a try-square. Now saw along these marks, making each cut just deep enough to bring the mortises diagonally across the piece from one corner to the opposite corner as shown in the detail sketch. Be careful not to get the mortises wider than the shelves are thick. Bevel the tops of the posts as shown.

Detail of the Magazine Rack

Detail of the Magazine Rack

Magazine Rack Complete

Magazine Rack Complete

See that the ends of the shelves are square and smooth, then set a scratch gauge so that the scriber is just 2 in. from the face of the block and mark this distance off each way from the corner of the shelves. Saw these corners diagonally across as shown, being careful not to saw off too much. 

The parts can now be assembled. Place all the parts in position, then pass a rope around each end and twist it up tightly with a small stick. If this is properly done, you can now pick up the rack and handle it in any way you wish. The screws can now be put in the corners. You can use flat-head screws and plug the holes, or you can use round-head blue screws and let the heads project. After the screws are all in, dress off all unevenness where the shelves are mortised into the posts, then mark each shelf and post so that you can put it together again after the parts are finished. Take the rack apart and transfer the marks to some part of the mortises and shelves that will not be covered with the finish you intend to put on. Apply the finish you wish to use and when the parts are thoroughly dry they can be reassembled and your rack will be complete.


Mission Furniture

  1. A PIANO BENCH
  2. A LIBRARY TABLE
  3. A PRINCESS DRESSER
  4. A SEWING BOX
  5. A FERN STAND
  6. A WARDROBE
  7. A FINISH
  8. AN OAK TABLE
  9. BOOK TROUGH
  10. AN OAK SERVING TABLE
  11. AN UMBRELLA STAND
  12. A CHAFING-DISH BUFFET
  13. A WRITING DESK
  14. MUSIC RACK AND BOOKSTAND
  15. A DICTIONARY AND MAGAZINE STAND 
  16. A LEATHER BACK ARM CHAIR 
  17. A WALL SHELF
  18. A PEDESTAL
  19. MAGAZINE RACK
  20. A HALL TREE
  21. A TABLE FOR THE DEN 
  22. A BURLAP-COVERED WINDOW SEAT 
  23. QUARTER-SAWED OAK SETTEE 
  24. A SCREEN
  25. A MISSION BOOKRACK 
  26. A ROUND EXTENSION DINING TABLE 
  27. AN ARM DINING CHAIR 
  28. A HALL BENCH
  29. A SEWING TABLE
  30. A SIDE CHAIR
  31. ANOTHER PIANO BENCH 
  32. ANOTHER SCREEN
  33. A FOLDING CARD TABLE 
  34. MAGAZINE STAND
  35. A TABOURET
  36. A PORCH SWING
  37. A FOOT WARMER
  38. A PLATE RACK FOR THE DINING ROOM 
  39. A MISSION SIDEBOARD 



                                                                

Basic Construction And Carpentry Techniques Home







Google




Written and maintained by
Ronald Hunter
           
  All images and text are copyright Ronald Hunter 2005, 2006, 2007, 2008 & 2009.
  All rights reserved
Top